In line chillers

tkromer

New member
Joined
Aug 7, 2007
Messages
20
Reaction score
1
Points
0
Location
Morgantown, WV, US
Country
United States
Display Name
Tommy
I am looking at getting an Eheim Ecco 2232 (or maybe the 2234) for a 40 gallon "breeder" aquarium. I'll be keeping 2 axolotls in this. I am looking to get a nice small 1/10hp or 1/6hp in-line chiller. Unfortunately all of these recommend ridiculous flow rates (like 500GPH). Any reason why underdriving the chiller -- 100-130GPH would be a problem?

--Tommy
 
Can you give us a link to see the chiller?
 
I don't really have experience with aquarium chillers but our water chillers(cold baths) at work pump at rediculously high flow rates. When the water flow is obstructed on ours or the pump itself is turned off, the water in the chiller will freeze up and you have to wait an hour for it to thaw again. I'm sure there must be a company that makes less heavy duty chillers.
 
you could take a second tank for cooling with the chiller with a high flow rate and a low flow rate from the second tank to your Axo-tank. Maybe there's a possible other way to keep water cool with pc coolers [don't know where you are living and what temperatur difference between tank and flat is supposed to increase ;) ]?

I'm afraid these chillers all have high flow rates ... otherwise they won't reach their technical efficiency [if you would like to speak about efficiency at all].
 
I'm going for about 7-8 degrees F below room temperature. The smallest refrigeration style I can find are 1/10hp. Below that you have peltier (thermoelectric) and they won't cool a 40 gallon aquarium. I'm sure efficiency will be sacrificed if you cut the flow rate, but I wonder if the cooler would freeze up or continue to work even with the low flow rate.

--Tommy
 
Well I've written several companies and I finally have an answer to my question. Figured I'd share the results with everyone who may be in the same boat as me.

The two companies I have found who make 1/15HP chillers both agree they are powerful enough to chill 40 (and they claim up to 60) gallons of water.

One company recommends 300 and the other 350GPH as a minimum flow, but upon contact they both believed 100GPH would be the absolute minimum to not worry about freezing/damage to the chiller. At 130GPH they said the chillers should be able to keep my water around 62-64 in a 71-72 degree (F) room. The one representative told me that efficiency might be somewhat sacrificed -- the chiller would run more frequently than if it were getting optimum water flow.

So in short, for those of you who need a small chiller and don't want all that flow aggravating your caudates, shoot for over 100GPH and you should be good to go.

--Tommy
 
TKR, thank you for sharing the details you found. This will surely help some other folks who may find themselves in the same quandary.

Sam, it depends on (1) the type of lid on the tank, and (2) the level of humidity in your air. And other factors too, perhaps. In general, I've found that fans will cool water by 1 or 2 degrees C (2-4 degrees F).
 
yea thanks tommy, keep us informed on how it works when you get it set up,, lowest temp it goes to etc, I think they only go down to 15 C but I might be wrong,

cheers
 
Well I'm hoping to get the tank set up in January so it will be a while but I'll definitely let everyone know how it works out!

--Tommy
 
thankyou tommy, it was only when I actually started getting my chiller (Boyu 150L) to work that I realised how usefull your findings are.

I was looking at the cooler sellers recommended fluval 305 which has 1000 LPH (too much methinks), is this the same as GPH?

Anyway I then found the fluval 205 which has a 110 GPH, I think this one should be ideal.
 
How is your temperature in comparison to the room temperature now that everything is setup Sam?

--Tommy
 
wrong pump

Alas I have not yet got it operational, I baught a fluval 205 pump to move the water through the cooler, but I dont think the flow rate is enough to get the water through because it just doesn't go!! The seller did recomend something like a fluval 405 but I thought wow, to much current for caudates and got the 205 because I am a fool.
Anyway going to get back on with it now and get it working, plead for an exchange of pump, let you know the details, I had to take a few days off because it was eating my soul..
 
General chit-chat
Help Users
  • No one is chatting at the moment.
    There are no messages in the chat. Be the first one to say Hi!
    Back
    Top